Product Overview
The ALSTOM BGTR 8HE is an industrial 8-slot VME rack associated with the PIB 903 interface and Converteam/Alstom control-system architecture. Current listings identify the assembly as BGTR 8HE / PIB 903, with eight VME slots for installing compatible processor, I/O, communication, and interface boards.
This rack is intended as a system-level chassis rather than a standalone controller. It provides the mechanical mounting and VME backplane environment required by the associated Alstom/Converteam electronics. A related listing also identifies the assembly with PIB100G and PIB310 boards and a 100–240 VAC, 50/60 Hz power supply arrangement.
The BGTR 8HE is particularly useful for maintaining legacy VME-based industrial and marine automation installations where replacing the complete control platform is not practical.
Product Datasheet
| Parameter | Specification |
|---|---|
| Brand | ALSTOM |
| Model | BGTR 8HE |
| Product Type | Industrial VME Rack / Chassis |
| Interface | PIB 903 |
| Slot Configuration | 8 VME Slots |
| Rack Height | 8HE |
| Associated Platform | Alstom / Converteam VME Control System |
| Power Supply | 100–240 VAC, 50/60 Hz, depending on fitted power assembly |
| Condition | Used / Surplus depending on inventory |
| Application | Industrial, power, marine and automation control systems |
The 8-slot configuration and BGTR 8HE designation are directly supported by current marketplace listings. The 100–240 VAC specification is reported for a related Converteam BGTR assembly and should be verified against the actual power-supply module fitted to the rack.
Key Features
- 8-slot VME rack architecture
- Alstom / Converteam BGTR 8HE platform
- Associated PIB 903 interface
- Designed for modular VME control-system construction
- Suitable for processor, I/O, communication and interface cards
- Supports maintenance of legacy control cabinets
- Useful for replacement of damaged or aging VME rack assemblies
- System-specific backplane and power configuration should be verified before installation
VME System Integration
The BGTR 8HE provides the physical framework for a group of VME-based control modules. Depending on the original system configuration, installed boards may include processor, I/O, communication, interface, or application-specific cards.
The rack should therefore be evaluated together with the complete installed configuration. Before replacement, compare:
- Number and position of installed VME cards
- Backplane connector arrangement
- PIB 903 identification
- Power-supply module and input voltage
- Board addressing and jumper settings
- VME bus configuration
- Cooling and airflow arrangement
- Cabinet wiring
- Existing Alstom/Converteam system documentation
Do not assume that every VME board is interchangeable simply because it fits mechanically. Bus configuration, slot assignment, addressing and system software can all affect compatibility.
Associated Components
Current listings for the BGTR 8HE/PIB903 assembly also reference PIB100G and PIB310 Converteam PCB cards, while another listing identifies the assembly with power-supply reference 24491 276A1004. These should be treated as configuration references rather than universal accessories for every BGTR 8HE rack.
Industrial Applications
The BGTR 8HE VME rack can be encountered in legacy control environments such as:
- Power-generation automation
- Industrial drive and converter systems
- Marine automation
- Process-control equipment
- Railway and transportation control
- Heavy industrial machinery
- Legacy Alstom/Converteam control cabinets
- VME-based supervisory and monitoring systems
Installation & Maintenance
1. Verify the Assembly
Confirm BGTR 8HE, PIB 903, rack slot count, and all visible identification labels before installation.
2. Inspect the Backplane
Check VME connectors for bent, damaged, oxidized, or contaminated contacts. Inspect the backplane for cracked solder joints or mechanical damage.
3. Verify Power
Check the installed power-supply assembly and confirm that the incoming voltage matches the original cabinet configuration. Do not rely solely on generic BGTR specifications.
4. Check VME Card Positions
Record the original slot positions of every processor, I/O, communication, and interface board before removing them.
5. Check Grounding
Ensure the rack chassis and cabinet protective earth are correctly connected before energizing the equipment.
6. Power-Up Test
Apply power according to the approved maintenance procedure and monitor system diagnostics, board status indicators, VME communication, and controller startup.
Troubleshooting
VME modules are not detected:
Check board seating, VME connectors, slot position, backplane condition, addressing, and bus configuration.
The rack does not power up:
Verify the installed power supply, incoming voltage, fuses/protection devices, internal connections, and chassis grounding.
Only some modules fail to communicate:
Inspect the affected slot and corresponding VME connectors. Compare the current configuration with the original slot arrangement.
The system repeatedly resets:
Check power stability, VME bus connections, processor status, and individual installed boards. A defective module can affect the common bus or power distribution.
A replacement rack appears mechanically identical but does not operate correctly:
Compare the backplane, PIB 903 configuration, power assembly, connectors, jumpers, and revision markings. Mechanical fit alone does not establish electrical compatibility.
First-Operation Checklist
☐ Confirm ALSTOM BGTR 8HE identification
☐ Confirm 8-slot VME configuration
☐ Verify PIB 903 identification
☐ Record original VME slot assignments
☐ Inspect backplane connectors
☐ Check installed power-supply assembly
☐ Verify incoming voltage and frequency
☐ Check cabinet grounding
☐ Inspect all installed VME boards
☐ Power up and verify system diagnostics
FAQ
What is the ALSTOM BGTR 8HE?
It is an 8-slot VME rack/chassis used with Alstom/Converteam control-system hardware. Current listings specifically identify it as a BGTR 8HE 8-slot VME rack with PIB 903.
What is PIB 903?
PIB 903 is the interface designation associated with the BGTR 8HE assembly in current industrial spare-parts listings. The exact function and configuration should be verified against the physical unit and original system documentation.
Is the BGTR 8HE a PLC?
No. It is a VME rack/chassis designed to accommodate compatible control and interface boards.
How many VME cards can it accommodate?
The listed BGTR 8HE configuration provides 8 VME slots.
What power supply does it use?
A related Converteam listing specifies 100–240 VAC, 50/60 Hz, but the exact power arrangement should be checked on the actual rack because configurations can differ.
Can another 8-slot VME rack replace it?
Not automatically. The backplane, power distribution, mechanical dimensions, PIB/interface arrangement, slot configuration, and system wiring must all be compared.
Related Alstom / Converteam Components
- ALSTOM PIB 903
- ALSTOM BGTR 8HE
- Converteam PIB100G PCB
- Converteam PIB310 PCB
- Converteam PIB101C
- ALSTOM VME processor modules
- ALSTOM VME I/O modules
- ALSTOM VME communication boards
- ALSTOM industrial control racks
- Converteam legacy VME control-system components
Compatibility among these components should always be confirmed against the original cabinet configuration, hardware revision and system documentation.
Spare-Parts & Lifecycle Planning
For legacy VME installations, the rack itself can become a critical spare because backplane damage, connector wear, power-distribution faults, or mechanical deterioration can be difficult to repair in the field.
A practical lifecycle strategy is to maintain:
- One verified spare rack for critical systems
- Documented VME slot assignments
- Spare PIB/interface boards where required
- Verified replacement power-supply assemblies
- Records of board revisions and configuration
- Periodic inspection of VME connectors and backplane contacts
- Last-time-buy planning for discontinued Alstom/Converteam hardware
When purchasing a replacement, the safest identification is the complete combination of BGTR 8HE + PIB 903 + installed power assembly + VME backplane configuration, rather than relying on the rack name alone.


