⚙️ Product Introduction
The Woodward 9907-028 Rev. F SPM-A Synchronizer is an electronic generator synchronization device designed for industrial power generation and generator control applications.
The SPM-A (Synchronizer and Load Control) series is designed to coordinate generator synchronization with an electrical bus. It monitors electrical operating conditions, including generator frequency and phase relationship, and provides control signals to the governor and circuit breaker system to support accurate synchronization.
The 9907-028 is suitable for applications where reliable generator connection and coordinated power system operation are required.
Typical applications include:
-
Industrial generator synchronization systems.
-
Power station automation.
-
Marine generator control panels.
-
Standby and emergency power systems.
-
Multiple-generator installations.
-
Industrial engine-driven power generation.
The Rev. F designation identifies the hardware revision. Before replacing an existing unit, verify the complete part number, electrical ratings, sensing configuration, and control wiring.
📋 Product Datasheet & Parameters
| Parameter | Specification |
|---|---|
| Brand | Woodward |
| Model | 9907-028 Rev. F |
| Series | SPM-A |
| Product Name | Speed and Phase Matching Synchronizer |
| Place of Origin | United States (manufacturer origin; individual unit origin unverified) |
| Product Status | Industrial electronic synchronizer |
| Dimensions | Exact enclosure dimensions not confirmed |
| Weight | Approx. 2.2 kg (5 lb) |
| Rated Power / Input | Maximum 5 W; 115 or 230 VAC, 50/60 Hz |
| Discontinued Status | Current production status not confirmed |
Additional Technical Specifications
-
Operating frequency: 50/60 Hz.
-
Phase matching window: ±10°.
-
Voltage matching: Not available.
-
Bus voltage input: 115 or 230 VAC RMS.
-
Generator voltage input: 115 or 230 VAC RMS.
-
Input voltage tolerance: ±10%.
-
Match-up time: Selectable 1/8, 1/4, 1/2, or 1 second.
-
Operating modes: RUN, CHECK, PERMISSIVE, OFF.
-
Synchronizer reset: Automatic.
-
Breaker close relay: Normally open contact.
-
Breaker close command duration: Approximately 1 second.
-
Maximum relay contact rating: 10 A at 28 VDC resistive or 3 A at 120 VAC resistive.
-
Operating temperature: -45°C to +70°C.
-
Compatible controls: Woodward 2301, 2301A, EPG, and 2500 series, depending on output configuration.
Technical specifications are based on Woodward SPM-A Synchronizer Manual 82384. The 9907-028 is a frequency and phase synchronizer without automatic voltage matching.
🔧 Daily Maintenance & Care
1. Visual Inspection: Regularly inspect the synchronizer housing, terminal connections, mounting hardware, and wiring for damage or corrosion.
2. Voltage Inspection: Check generator and bus voltage sensing circuits to ensure that input signals remain within the specified operating range.
3. Frequency Monitoring: Verify generator and bus frequency readings and ensure that the connected governor maintains stable engine speed.
4. Terminal Maintenance: Inspect electrical terminals and connectors for loose connections, oxidation, and overheating.
5. Relay Testing: Periodically test the breaker-close relay and confirm that the external circuit breaker responds correctly.
6. Parameter Verification: Check phase matching settings, match-up time, operating mode, and output configuration.
7. Environmental Protection: Keep the control cabinet clean, dry, and properly ventilated.
8. Wiring Inspection: Examine speed-bias connections and voltage sensing cables for insulation damage and electrical interference.
9. Maintenance Records: Record synchronization test results, configuration changes, and replacement history.
10. Preventive Testing: Perform functional testing according to the generator manufacturer’s recommended maintenance schedule.
🛠️ Troubleshooting & Common Problems
1. Synchronizer Does Not Start
-
Check the input voltage connections.
-
Verify the 115/230 VAC configuration.
-
Inspect wiring terminals and external protection devices.
-
Check the selected operating mode.
2. Generator Frequency Cannot Be Matched
-
Inspect the magnetic speed sensor.
-
Check the governor speed-control system.
-
Verify speed-bias output connections.
-
Inspect frequency differences between the generator and bus.
3. Phase Synchronization Failure
-
Check generator and bus voltage sensing connections.
-
Verify phase sequence and wiring.
-
Inspect phase offset settings.
-
Confirm that the phase difference is within the ±10° matching window.
4. Circuit Breaker Fails to Close
-
Check the breaker-close relay.
-
Inspect external breaker control wiring.
-
Verify breaker permissive conditions.
-
Check whether the synchronization requirements have been satisfied.
5. Synchronization Is Unstable
-
Inspect speed-bias wiring.
-
Check generator frequency fluctuations.
-
Verify governor response and adjustment settings.
-
Inspect voltage sensing circuits for interference.
6. Incorrect Synchronization Signals
-
Check voltage transformer connections.
-
Inspect the generator and bus sensing inputs.
-
Verify the output impedance configuration.
-
Check compatibility with the connected Woodward governor.
7. Synchronizer Remains in CHECK Mode
-
Inspect the external mode selector switch.
-
Verify the control wiring.
-
Check the selected operating mode.
-
Confirm that the breaker-close circuit is configured correctly.
⚠️ Safety Precautions
-
Installation and maintenance must be performed by qualified electrical technicians.
-
Disconnect electrical power before changing wiring or servicing the synchronizer.
-
Confirm the correct 115 VAC or 230 VAC input configuration before energizing.
-
Never exceed the specified voltage and relay contact ratings.
-
Verify generator phase sequence before synchronization.
-
Never manually close a generator breaker without confirming synchronization conditions.
-
Keep independent overspeed and generator protection systems operational.
-
Do not bypass circuit breaker interlocks or protective devices.
-
Ensure all electrical terminals are properly insulated.
-
Avoid operating the equipment in environments with excessive moisture, dust, or corrosive substances.
-
Test the complete synchronization and breaker control circuit before returning the generator to service.
🔩 Recommended Woodward Models
The following 15 Woodward models are recommended for generator synchronization, speed regulation, load sharing, and power management applications.
| No. | Model | Product Description |
|---|---|---|
| 1 | 9905-001 | SPM-A Synchronizer |
| 2 | 9905-002 | SPM-A Synchronizer, 1% Voltage Matching |
| 3 | 9905-003 | SPM-A Synchronizer, 5% Voltage Matching |
| 4 | 9905-004 | SPM-A Synchronizer, ±5° Phase Matching |
| 5 | 9905-005 | SPM-A Synchronizer, 1% Voltage Matching |
| 6 | 9905-006 | SPM-A Synchronizer, 0.5% Voltage Matching |
| 7 | 9905-008 | SPM-A 400 Hz Synchronizer |
| 8 | 9905-009 | SPM-A Synchronizer, 10% Voltage Matching |
| 9 | 9905-107 | SPM-A Synchronizer, 5% Voltage Matching |
| 10 | 9907-029 | SPM-A Synchronizer with Voltage Matching |
| 11 | 9905-096 | Automatic Generator Loading Control |
| 12 | 9905-131 | 2301A Speed Control |
| 13 | 9905-797 | Digital Synchronizer and Load Control |
| 14 | 8280-488 | 723 PLUS Digital Control |
| 15 | 8406-121 | EGCP-2 Digital Generator Control |
The SPM-A model specifications are referenced against Woodward Manual 82384. Other models are related Woodward generator control products and are not necessarily interchangeable with 9907-028.


